Stator + Gasket + Flywheel + Puller fit Ski-Doo Grand Touring Renegade 2009-2016

Description

Free
shipping in USA
Same day
shipping
visit our store >
find parts for :
ATV / UTV / SXS
Motorcycles
Snowmobiles
Watercraft
Other
Menu
Store Home
find parts for
ATV / UTV / SXS
Motorcycles
Snowmobiles
Watercraft
Other
Kit Stator + Gasket + Flywheel + Flywheel Puller for Ski-Doo Expedition Grand Touring Renegade GSX GTX 1200 2009-2016
Brand New Kit Stator + Gasket + Flywheel + Flywheel Puller
Direct replacement to your original unit
Plug-and-play, direct fit, easy installation
All shipped products are tested
*All item pictures are accurate, if in doubt, do not hesitate and compare our item to your original part.
Stator
Highest grade of lamination materials
Highest grade of copper winding, resistant to 200 degrees Celsius
Connector included
Rubber grommet included
Flywheel Puller
38 mm x 1.5 Right hand male
Vehicle models fitment
Ski-doo Expedition 1200 SE TUV EFI L/C -- 2010-2016
Ski-doo Expedition 1200 TUV EFI L/C -- 2010-2016
Ski-doo Grand Touring 1200 EFI L/C -- 2010-2015
Ski-doo GSX 1200 EFI L/C -- 2009-2015
Ski-doo GTX 1200 EFI L/C -- 2009
Ski-doo MX Z 1200 Adrenaline EFI L/C -- 2010
Ski-doo MX Z 1200 EFI L/C -- 2009-2014
Ski-doo MX Z 1200 Renegade EFI L/C -- 2009
Ski-doo MX Z 1200 TNT EFI L/C -- 2011
Ski-doo MX ZX 1200 EFI L/C -- 2009-2015
Ski-doo MX ZX 1200 Renegade EFI L/C -- 2009
Ski-doo Renegade 1200 Adrenaline EFI L/C -- 2010-2015
Ski-doo Renegade X 1200 EFI L/C -- 2010-2015
OEM part replacement
RMS900-101523-R00
Specifications
Stator Dimension:
Interior diameter: 42 mm
Exterior diameter: 114 mm
Thickness: 19 mm
Length of wires stator to grommet: 110 mm
Length of wires grommet to plug: 600 mm
Other specifications:
Number of wires: 3
Number of plugs: 1
Number of pins: 3
Flywheel Puller Dimensions:
Length: 103 mm
Exterior Diameter: 45 mm
Interior Diameter: 37 mm
Exterior Diameter Center Housing: 14 mm
instructions
Stator:
Before installing your new Stator
Check the AC output of the stator
Replace any burned or corroded connectors on stator and regulator rectifier
Check and repair any melted wiring
Use hi-temp dielectric grease on all connectors
Our stator might have a different wire color code than your original part.
All the wires are installed in the correct order; please do not change any of the wiring configurations.
This stator is designed as a direct plug-in replacement and should be used as such.
When bolting stator in, always use locking compound.
If our stator includes a pickup coil, always make sure the air gap is correct upon installation; we suggest as close as possible but no less than 0.010".
Flywheel:
Before attempting to start your Ski-Doo, adjusting the air gap is necessary. Rotate the flywheel so the raised node is lined up with the pick up/pulser coil and adjust as close as possible but no less than 0.010??.
Flywheel Puller:
How it Works
Flywheel Pullers are very versatile engine service tools and are a must in every toolbox. Our large selection of best selling rotor and flywheel pullers fit just about any motorcycle or ATV. Flywheel pullers are very simple to use, having only an outer body to hold the flywheel and a screw to push on the crankshaft. Some are even simpler, having only a bolt to thread into the flywheel. A taper holds the flywheel or rotor and the crankshaft together. The flywheel is secured to the shaft by applying torque to the fixing bolt.
An Important Component to use
Many flywheel or rotor puller tools will include a small cap. This is a crankshaft thread protector, and should always be used if it is included with the puller. You slip this cap onto the end of the inner piece of the puller which presses against the tip of the crankshaft. This keeps the fine threads from being stripped or damaged while removing the flywheel or rotor.
Actions to Avoid
Most of the time, removing a flywheel or rotor is painless. But sometimes corrosion, over-torquing the fixing bolt, or heat-cycling can give you a hard time removing the flywheel. We too often see mechanics use a larger breaker bar or air impact tools to ease the flywheel off. These two techniques will damage the flywheel, the flywheel puller, or the crank. Avoid using them if you want to keep it cheap.
Tips to break a stuck flywheel loose:
Torque Wrench
How do you know if it?s stuck? You simply have to set your torque wrench to 50 ft-lbs and try to ease the flywheel off. If the flywheel is not stuck, you should be able to remove it with even less torque than this. If it is stuck, don?t use more torque or you might break your wrench.
Ball Peen Hammer
If 50 ft-lbs does not do the trick, go fetch something like a 12 or 16 oz ball peen hammer. Hit the end of the flywheel puller with a medium blow. Many times, the shock you create will successfully remove your flywheel. Be prepared to catch the flywheel since the shock of the hammer can make the flywheel jump off. Once again, getting into that situation will be pricey. And don?t forget your safety glasses.
Propane Torch
The hammer is not a be-all, end-all solution. Sometimes, you will have to find something more powerful, and that?s where the propane torch comes in. As a last resort solution, the heat should expand the flywheel but not the crank, since it is too massive to expand as fast. That way, the flywheel will become looser and will come off easier.
Important Security Tips:
In order to not set fire to your garage, your vehicle, or yourself, certain precautions are necessary prior to heating the flywheel:
Clean any oil or flammable liquids off the flywheel;
Make sure your work area is free of any flammable liquids and that you work in a well ventilated area;
Make sure to remove the gas tank, and set it aside at a safe distance.
Make sure the flame of your torch is focused, and heat only the center of the flywheel. This is due to the fact that some flywheels use adhesive or other fixing compounds to locate the magnets in the rim that can be damaged by concentrated heat. Here again, the wheel might fall off the crank, so be prepared to catch it. And remember that you just heated it, so make sure you can catch it without burning yourself.
With these tips and techniques, you are now equipped to handle any stuck flywheel without throwing your flywheel puller at it; unless you have a habit of working with machines that have been in a lake for months!
SHIPPING
We deliver 99.4% of our orders within the specified time period. If your item is not available in our main Colorado facility, we still guarantee that your order will be delivered within the specified time period.
If your item is not delivered within this time period, we will offer you a 5.00$ discount on your order. This guarantee applies to shipments delivered in the 48 continental USA states, excluding PO boxes.
Videos
customer service
AsK seller a question
duties & taxes
International Buyers:
Import duties, taxes, and charges are not included in the item price
or shipping cost. These charges are the buyer's responsibility.
RaceTech Electric was founded in 2011 by three motorcycle industry veterans in San Diego, CA. The group has over 20 years combined in the Motorcycle industry.
Customer service
Part request
About us
About seller page
Add seller to favorite